Home / Brands / Amana / Laundry appliances / Washer
Amana · Washer repairAmana washer repair in Denver
Drain pumps, door boots on front-loaders and lid switches on top-loaders.
Book Amana washer repair
We reply during business hours (Mon–Sat 7am–7pm · Sun 8am–6pm). Urgent? Call (720) 534-0432.
16 Amana washers repaired in our records
From our job records since 2024. Problems as reported by customers; parts where the technician recorded a replacement.
Most common complaints
- Not working
- 4
- Not draining
- 1
- Leaking water
- 1
Parts we replaced most
- Control board
- 3
- Drain pump
- 2
Recent Amana washer jobs
- June 2026 · Not draining; replaced the drain pump · Longmont
Washer problems we diagnose
General washer faults we check on Amana models. Full washer repair guide →
Washer won't drain
Water sitting in the drum after a cycle is usually a clogged drain pump filter (on many front-loaders there's a small access door at the bottom front), a sock in the pump, a kinked drain hose or a failed pump. We clear it, test the pump and check the standpipe height.
Won't spin or stops mid-cycle
Most spin faults are safety switches doing their job: a lid switch or door lock that doesn't confirm, an out-of-balance load, or a drain problem the control reads as 'not empty'. Past that, it's a belt, motor coupler, shift actuator or motor control.
Leaking water
On front-loaders, a torn door boot or a clogged drain causing overflow are common. On any washer, we check fill hoses, the pump and the tub seal. Leaks under the machine that only show during spin are often a pump or hose connection.
Error codes and blinking lights
Error codes narrow the search but rarely name the part. An LG OE, a Samsung 4C or a Whirlpool F21 can each have three or four causes. We test before we replace.
Loud banging or grinding during spin
Banging is usually a load imbalance, worn suspension rods or shocks, or a machine that isn't level. A roaring or grinding noise that gets louder over months is typically tub bearings — a bigger repair we'll price before starting.
Washer won't fill or fills slowly
Closed or partly closed supply valves, kinked hoses, clogged inlet screens or a failed inlet valve. Hard water deposits in the screens are a frequent cause in some parts of the metro.
Door won't unlock after the cycle
Water still in the drum, a failed door lock or a control that didn't finish the cycle. Don't force the door; we drain the machine and release the lock safely.
Clothes still soaking wet
Weak spin from a drain that's not fully clearing, an out-of-balance load, worn suspension or a motor control fault. We check the drain first because it's the most common cause.
Washer moves across the floor
Uneven floors, unadjusted leveling legs, worn suspension or — on new machines — shipping bolts that were never removed.
How we check a Amana washer
- We start with the error history if the control stores one, and with what the machine does: does it fill, agitate, drain and spin?
- We check the drain path — pump filter, pump, hose and standpipe — because drainage problems cause many spin and error complaints.
- We test the door lock or lid switch and the signals the control uses to confirm the door is closed.
- For noise and vibration we check leveling, suspension, the drum and the bearings.
- For leaks we run a short cycle with the panels off to see exactly where water comes from.
Where we repair Amana washers
When Amana washers break
In our records, the busiest months for Amana washers are April and March; the quietest is July. Booking early in a busy month gets you a faster appointment.
Completed jobs by month, 2024–2026.
Amana washers we service
Front-load washers
Front-loaders use less water and spin faster, which makes the door lock, door boot, drain pump and suspension work hard. Most have a drain filter behind a small panel at the bottom front that needs regular cleaning.
Top-load agitator washers
The traditional design with a center agitator. Lid switches, drive couplers, transmissions and drain pumps are the typical repairs, and they're usually straightforward.
High-efficiency top-loaders
Impeller or wash-plate top-loaders spin faster and use less water than agitator models. Shift actuators, lid locks, suspension rods and motor controls are common service points.
Stacked and laundry-center units
Stacked pairs and one-piece laundry centers save space but limit access. Some repairs require separating or pulling the units out, which adds time.
Washer-dryer combos
All-in-one machines wash and dry in the same drum. They combine washer parts with a condenser or heat-pump drying system and take longer to diagnose.
Before you call: Amana washer
- Check the drain pump filter on front-loaders. Put down towels — a full drum can release a lot of water.
- Make sure the door or lid closes fully and nothing is caught in the gasket.
- Check the drain hose for kinks and the standpipe for clogs.
- Confirm both water supply valves are fully open.
- Redistribute the load if the machine stops on spin; heavy items like towels and bedding can unbalance it.
- Look up the error code in your manual, but call us before replacing parts — codes point to an area, not a specific part.
What affects the price
- Pumps, switches, valves and belts are moderate repairs; tub bearings and transmissions take much more labor.
- Stacked units and laundry closets can add time to access the machine.
- Machines that need to be drained by hand before service take a little longer.
How long they last
Most washers last about 10 to 13 years. Repairs to pumps, door locks, switches, valves and belts are almost always worthwhile. Tub bearings and transmission repairs are larger jobs; on newer or premium washers they're often still worth it, while on older economy machines replacement may make more sense.
How a home repair visit works
Book
Call, text or send the form with the appliance, brand and model if you have it. We give you an arrival window.
Diagnose & quote
The technician tests the appliance and gives you a written price before starting. The service call is credited if you go ahead.
Repair & warranty
Most repairs are finished on the first visit with parts from the truck. Every repair carries our 90-day warranty.
Amana washer repair: common questions
What usually fails on a Amana washer?
In our Amana washer jobs, the parts we record most often are control board and drain pump. Every unit is tested before parts are ordered.
Is it worth repairing a Amana washer?
Pumps, switches, belts, door locks and valves are worth fixing on almost any washer. Tub bearings on an older, inexpensive top-loader sometimes aren't — we'll show you the numbers.
How much does Amana washer repair cost?
The service call starts from $59 and is credited toward the repair. The total depends on the part and labor; you get a written price before any work.
Do you repair Amana washers under warranty?
Warranty repairs should go to Amana's authorized servicer. We repair out-of-warranty units.
Other washer brands we repair
Photos from our job records
Real photos our technicians took on calls around Denver and the Front Range. Each caption says what was done; no customer details are shown.







