Home / Guides

Cooking · 8 min read

Gas stove burner won't light or keeps clicking

On ranges and cooktops, a burner that won't light is the complaint we hear most, 108 of 310 range and cooktop jobs in our records. Most of them are cleaning and alignment problems you can fix yourself in ten minutes. The rest are electrodes, switches and spark modules, all routine repairs.

By the ABC Denver service team · Updated November 2026

A KitchenAid gas range after service in Boulder
108burner-not-lighting calls
310range & cooktop repairs since 2024
28igniters replaced on ranges
90 daysparts and labor warranty
Short answer

If the burner clicks but won't light, the cap is usually misaligned or the ports are clogged. If there's no click at all, check power and the spark module. If one burner clicks constantly, the switch behind that knob is wet or failed. If the flame is yellow, lifts off the burner or is noisy, the air-gas mix needs adjusting, which at Denver altitude is a common setup issue. If you smell gas, leave and call your gas utility first.

How a sealed burner lights

When you turn the knob, a switch behind it tells the spark module to fire. The module sends a high-voltage pulse to the electrode next to every burner (that's why they all click), and the spark jumps to the burner cap. Gas flowing through the burner ports is lit by that spark. Once you release the knob to a setting, the clicking stops.

Each step can fail: no gas reaching the ports, no spark, a spark in the wrong place, or a switch that never stops sparking.

What happensLikely causeFix
Clicks, no flameCap misaligned, ports clogged, wet burnerClean, dry, reseat cap
Clicks, lights slowly or with a popPartly clogged ports, weak sparkClean ports, check electrode gap
No click on any burnerNo power, spark module, wiringCheck outlet, test module
No click on one burnerElectrode or its wire, cracked ceramicReplace electrode
One burner clicks constantlyWet or failed igniter switchDry out, then replace switch
Yellow, lazy or lifting flameAir-gas mix, altitude setup, dirty burnerClean, adjust per manufacturer
A KitchenAid gas range after service in Boulder
A KitchenAid gas range after service in Boulder. Photo from one of our jobs.

Caps and ports: the ten-minute fix

Most burners that click but won't light have a cap sitting slightly crooked or ports clogged with boil-over. Lift off the cap and the burner head, wash them in warm soapy water, and clear each port with a soft brush or a wooden toothpick. Don't use a metal pin or a paper clip: it can enlarge the ports and change the flame.

Then let everything dry completely before reassembling, and make sure the cap sits flat and centered. On many models the cap only seats correctly one way.

Tech noteAfter a spill or after washing the caps, a burner can click and not light until it's fully dry. Give it a few hours, or dry it gently with a hair dryer, before assuming a part has failed.

The electrode

The small white ceramic post next to the burner is the electrode. If its ceramic is cracked, the spark can leak to the burner base instead of jumping to the cap. You may see a faint spark in the wrong place or hear clicking with no visible spark. Grease on the tip weakens the spark too. A cracked electrode is a simple replacement.

Constant clicking: the switch

If one burner keeps clicking after you've set the knob, or the clicking won't stop with all knobs off, the igniter switch behind a knob is stuck closed. Often it's wet from a spill that ran down the knob shaft. Turn off power to the range and let it dry for a day. If it still clicks, that switch, or sometimes the whole switch harness, gets replaced.

No clicking at all: power and the module

If none of the burners click, check that the range is plugged in and the outlet works. Gas ranges still need 120-volt power for the spark. If power is fine, we test the spark module, which generates the high-voltage pulses. A failed module stops every burner. On pro-style ranges from Wolf, Viking and Thermador, modules and reignition systems are common service points.

Flame color, lifting and altitude

A good flame is blue with small, steady inner cones. A yellow or orange flame, soot on pans, or a flame that lifts off the burner and roars means the air-gas mixture isn't right. Dirty burners cause some of it. The rest is setup.

At Front Range elevations there's less oxygen in the air, and many gas appliances call for a high-altitude adjustment or orifices from the manufacturer. A range moved from another home, converted between natural gas and propane, or installed without the altitude setup often shows lifting or lazy flames. We adjust per the manufacturer's instructions.

Tech noteIf you smell gas when a burner won't light, turn the knob off and ventilate before trying again. A strong or persistent smell is a reason to leave and call your gas utility from outside.

What our records show

Ignition is by far the biggest category on ranges and cooktops: 108 of 310 jobs. Only 28 of them have an igniter or electrode replacement recorded. Many of the others come down to cleaning, drying, reseating caps, switches and adjustments. On ovens the pattern is similar: 95 ignition calls and 54 igniters replaced. If your burner won't light, try the ten-minute cleaning fix before you book.

Range and cooktop complaintCallsPart replacedTimes
Burner not lighting108Igniter / electrode28
Not working43Control board12
Not heating14Heating element2

A cleaning routine that prevents ignition problems

Most ignition calls start with a spill. Boil-over runs into the ports, onto the electrode or down the knob shaft into the switch. A simple routine heads off most of them.

  • Wipe spills as soon as the burner cools, before they bake on
  • Every few weeks, lift the caps and heads and wash them in warm soapy water
  • Clear ports with a toothpick or soft brush, never metal
  • Dry everything completely before reassembling
  • Don't spray cleaner directly on the knobs; spray the cloth instead
  • Check that each cap sits flat and centered after cleaning

How we diagnose it on a service call

  1. 1Light each burner and note which ones fail and how
  2. 2Watch for spark at each electrode in a dim room
  3. 3Remove caps and heads, check port condition and cap seating
  4. 4Measure the electrode gap and inspect the ceramic
  5. 5Check the switch on any burner that won't stop clicking
  6. 6Test the spark module output
  7. 7Check flame color and lift on each burner
  8. 8Adjust air shutters or verify altitude setup per the manufacturer

Pro-style and dual-fuel ranges

Wolf, Viking, Thermador, BlueStar and Monogram ranges have higher-output burners, and many have automatic reignition that relights the flame if it goes out. That system adds its own sensing to the spark circuit. A burner that relights constantly or clicks while lit often points to a dirty or misaligned electrode, or moisture in the spark circuit.

Griddles and charbroilers on pro ranges have their own burners, thermostats and igniters. Our built-in and luxury appliance repair page covers these brands.

Glass-top and induction: different problems

Not every cooktop lights with a spark. Electric glass-tops heat with radiant elements under the glass, and their common faults are elements that won't heat, infinite switches that stick on high, and hot-surface indicator lights. Induction cooktops use power boards and coils, and their faults show up as error codes or a zone that won't detect the pan.

If your cooktop isn't gas, our stove and cooktop repair page covers those problems, and the error code lookup lists common codes.

When a burner problem is a gas problem

Most ignition issues are inside the range. A few are not. If every gas burner and the oven all have weak, small flames, or the flames got smaller after work on your gas line, the supply pressure may be low. If you recently switched from propane to natural gas or the other way, the range needs the right orifices and regulator setting for that fuel.

Those are setup items rather than worn parts. We check the regulator and orifices against the manufacturer's specification and adjust what we can on the appliance. Anything upstream of the range shut-off valve belongs to your gas utility or a licensed plumber.

Tech noteRange ignition systems are designed to be safe, but gas is not something to experiment with. If a burner won't light after cleaning and drying, turn the knob off and call. If you smell gas, leave first and call from outside.

Is it worth repairing?

Yes, almost always. Electrodes, switches and modules are a small fraction of the cost of a new range, and cleaning and adjustment costs even less. On pro-style ranges, repair is the clear choice.

Range ignition parts, explained

PartWhat it doesHow it fails
Burner capSpreads the flame and receives the sparkMisaligned, stops the spark lighting the gas
Burner head / portsDistribute gasClog with boil-over
Spark electrodeDelivers the sparkCeramic cracks, grease weakens spark
Igniter switchTells the module to sparkGets wet, sticks, clicks constantly
Spark moduleGenerates the sparkFails, no burners click
Orifice / air shutterSets the gas flow and air mixWrong size or setting, poor flame

Cost and when to call

Electrodes, switches and modules are moderate repairs; cleaning and adjustment is often all it takes. Call (720) 534-0432 if a burner still won't light after cleaning and drying, if clicking won't stop, or if the flame stays yellow. See also our stove and cooktop repair page, oven not heating guide and range installation.

Still not working?

Home service call from $59, credited toward the repair. Same- or next-day visits across the Denver metro.

Call (720) 534-0432

Questions we get about this

Why do all burners click when I turn one on?

They share one spark module. That's normal.

Is it safe to light a burner with a match?

In an emergency on most sealed-burner ranges, yes, carefully. Check your manual and never do it if you smell gas.

Why is my flame yellow?

Dirty burners, the wrong air-gas setting or a missing altitude adjustment. It should be checked.

My burner clicks forever after I cleaned the stove. Why?

Water got into the switch. Let it dry fully before replacing anything.

Can a burner fail to light because of low gas pressure?

Yes, though it's less common. If all gas appliances are weak, contact your gas utility.

Should I replace all electrodes at once?

Only the failed one, unless the spark harness or module is the problem.

Call (720) 534-0432