Dryer takes too long to dry: what's really slowing it down
A dryer that needs two or three cycles is one of the most common complaints we hear, and it's the one where people most often buy parts they don't need. There's heat, the drum turns, the clothes come out warm and damp. In our records, a dryer that is "not drying" more often has an airflow problem than a heat problem. Here is how we sort out which one you have, starting with the checks that cost nothing.

If the clothes come out hot and damp, the problem is almost always airflow: a clogged lint path, a crushed duct behind the dryer, or a long or blocked vent run. If they come out cool and damp, it's a heat problem: a weak element, a gas valve coil, or a thermostat. If the cycle ends early with damp clothes, look at the moisture sensor bars. Check the washer's spin too. Clothes that come out of the washer dripping will take any dryer twice as long.
Hot and damp, or cool and damp?
This is the most useful single question. Grab the clothes as soon as the cycle ends.
If they're hot to the touch but still damp, the dryer is making heat but the moisture can't leave. The water evaporates out of the clothes and has nowhere to go. That's an airflow problem: the lint path, the duct or the vent.
If they're only lukewarm and damp, the dryer isn't making enough heat. That's a heat problem: the element, the gas burner, or a thermostat that cycles too early.
If the cycle ends early on auto dry and the clothes are damp, the dryer thinks they're dry. That's usually the moisture sensor.
| What you notice | Most likely cause | What we check |
|---|---|---|
| Hot clothes, still damp | Restricted airflow | Lint path, duct behind dryer, vent run, vent hood |
| Warm or cool clothes, damp | Weak heat | Element resistance, gas valve coils, thermostats |
| Cycle ends early, damp clothes | Moisture sensor | Sensor bars coated with residue, sensor wiring |
| Laundry room gets hot and humid | Leak in the duct or a disconnected duct | Duct joints behind the dryer and in the wall |
| Dryer top is very hot to touch | Severe restriction | Full vent and blower inspection right away |

The lint path inside the dryer
The lint screen catches most lint, not all of it. The rest settles in the cavity below the screen, in the blower housing and in the internal duct. Over years, that becomes a felt mat that chokes airflow from the inside.
Pull out the screen and look down into the slot with a flashlight. If you see a layer of grey fluff, vacuum it out with a long narrow attachment. Dryer sheets also leave a waxy film on the screen. Hold it under the tap: if water beads up instead of passing through, wash the screen with warm water and a brush.
Inside the cabinet we find more. Lint packs around the blower wheel, the heater box, and on gas models around the burner. We clean those areas whenever a dryer is open, because lint near a heat source is both a drying problem and a fire risk.
The vent: where most slow dryers are fixed
Behind the dryer, a duct connects the dryer to the wall, and from there a vent pipe runs to an outside hood. If any part of that path is crushed, kinked, disconnected or packed with lint, airflow drops. With less airflow, drying times climb.
The most common problem we see is the short duct behind the dryer. It's often the soft foil kind, crushed when the dryer was pushed back against the wall. Replace it with semi-rigid aluminum duct and leave a few inches of space.
Then go outside while the dryer runs on high heat. You should feel a strong, warm stream of air at the vent hood. If it's weak, the vent run needs cleaning. Check the flap too. Lint, a bird nest, or a painted-shut flap can block the whole system at the very end.
- 1Unplug the dryer (and close the gas valve on a gas dryer) before moving it
- 2Disconnect the duct at the dryer and the wall and look through it
- 3Replace foil or vinyl duct with semi-rigid or rigid metal duct
- 4Brush or vacuum the vent run from the wall to the outside hood
- 5Make sure the outside flap opens freely and has no screen that traps lint

Long vent runs in Denver-area homes
Many homes around Denver have laundry rooms in the middle of the house, in a basement, or on the second floor. That means long vent runs with several elbows, sometimes running up through the roof. Every elbow adds resistance, and roof vents collect lint at the top where nobody can reach.
Dryer manufacturers list a maximum vent length in their installation guide. It's often in the range of 30 to 60 feet for rigid duct, minus several feet for each elbow, and it varies by model. Townhomes and newer builds sometimes push right up to that limit. A dryer that has always been a little slow in a home like that is usually telling you about the vent, not the dryer.
We recommend a full vent cleaning every year or two for long runs and roof vents. We do that as a separate dryer vent cleaning service. Clean airflow helps the drying time, protects the heating element and thermal fuse, and lowers the fire risk.
Weak heat: elements, gas valves and thermostats
If the clothes come out cool, we look at heat. On electric dryers, we check both halves of the 240-volt breaker first. If one half trips, the drum turns but there's no heat. Then we measure the element. A healthy element reads a steady resistance, often in the 7 to 12 ohm range. We replaced 144 heating elements in our records, more than any other dryer part.
Gas dryers have a burner that cycles on and off. If the burner lights, burns for a short time, then won't relight, the gas valve coils are usually getting weak. The dryer heats at the start of the cycle and then goes cold. That's a classic slow-dry complaint on gas models. At Denver altitudes we also make sure the burner and orifice are set up the way the manufacturer specifies for elevation.
Cycling thermostats can also drift. If one opens too early, the dryer keeps shutting off the heat before it's reached drying temperature. We test thermostats with a meter and measure the exhaust temperature during a test load. Guessing isn't good enough there.

Moisture sensors and auto-dry cycles
Most newer dryers have two metal bars inside the drum, usually near the lint screen. Wet clothes touching the bars complete a tiny circuit, and the control reads that as "still wet." When the bars get coated with fabric softener and dryer sheet residue, the control thinks the clothes are dry and ends the cycle early.
Wipe the bars with rubbing alcohol on a cloth. If the auto cycle still stops early, try a timed cycle on the same load. If timed dry works and auto dry doesn't, the sensor or its wiring is the next thing to test.
Some customers also use the delicate or low-heat setting without knowing it. Check the setting on the panel before anything else.
The washer can be the real problem
A dryer has to remove the water that the washer leaves behind. If the washer's final spin is weak, the clothes go into the dryer heavy and dripping, and drying time doubles.
Pick up a load right after the washer finishes. Damp is normal. Dripping isn't. If the washer isn't spinning out properly, see our washer not spinning guide. A worn belt, an unbalanced load or a drain problem often shows up first as "my dryer got slow."

Loading habits that slow drying
- Overloading: clothes need room to tumble. A packed drum dries in clumps
- Mixing towels with light shirts: the shirts dry first and the towels stay damp
- Single huge items: a comforter wraps into a ball and stays wet in the middle
- Too many dryer sheets: they coat the screen and the sensor bars
- Opening the door often: each time the dryer starts warming up again
When slow drying is a safety issue
Stop using the dryer and get it checked if you notice any of these: a burning smell, the top or sides of the dryer too hot to touch, lint coming out around the door, the laundry room getting hot and humid, or a thermal fuse that has already blown once. All of these mean the heat isn't leaving the dryer.
If your dryer has been slow for a while, book a dryer repair visit. We check the vent, the heat and the sensors in one visit and give you a written price before any work. For heat problems specifically, see our dryer not heating guide.
Still not working?
Home service call from $59, credited toward the repair. Same- or next-day visits across the Denver metro.
Related repairs from our jobs
Questions we get about this
How long should a normal dryer load take?
A typical mixed load usually dries in 40 to 60 minutes on normal heat. Towels and heavy cotton take longer. If a normal load regularly needs two cycles, something is restricting airflow or heat.
Is a clogged dryer vent dangerous?
Yes. Lint is flammable, and a blocked vent makes the dryer run hotter and longer. That's why we treat slow drying with a hot dryer cabinet as a priority.
Can I clean the dryer vent myself?
You can clean the duct behind the dryer and the outside hood. Long runs, roof vents and runs with several elbows are best cleaned with proper brushes and a vacuum system.
Why does my gas dryer heat at first and then stop?
Weak gas valve coils are the usual cause. The burner lights at first, then fails to relight once the coils warm up. It's a common, fixable repair.
Why does auto dry stop while clothes are still damp?
Residue on the moisture sensor bars makes the dryer think the clothes are dry. Wipe the bars with rubbing alcohol and try again.




