Home / Locations / Denver / Dryer repair

Denver, CO · Dryer repair

Dryer repair in Denver, CO

Clothes still damp after an hour, no heat, a squeal or a thump, or a dryer that won't start. We repair gas, electric and heat pump dryers across Denver, and we always check the vent, because that's where most dryer problems start.

Home service callfrom $59
Credited toward the repair when you go aheadWritten quote before any work · same- or next-day appointments · 90-day warranty on parts and labor

Book dryer repair in Denver

We reply during business hours (Mon–Sat 7am–7pm · Sun 8am–6pm). Urgent? Call (720) 534-0432.

Same / next-day visitsSeven days a week
90-day warrantyOn parts and labor
From $59Service call, credited with repair
Written quote firstNo work without your OK
InsuredLicensed for refrigerant work (EPA 608)
All major brandsStandard and built-in

In Denver, a dryer that takes two or three cycles to dry is usually not a broken dryer. It's a dryer that can't breathe: a crushed or lint-packed vent, a foil duct folded behind the machine, or lint buried inside the cabinet. Restricted airflow also overheats the dryer and blows thermal fuses, which is why 'no heat' and 'not drying' calls are so often the same problem.

Below are real dryer repairs from our Denver job records, with photos from those jobs. Lint buildup is also a fire risk, so if your dryer is getting unusually hot, stop using it until it's checked.

Not drying

Not drying: the vent and the cabinet

01A GE dryer that couldn't push air out

A GE dryer in Denver was leaving clothes damp. We removed and cleaned the exhaust duct behind the dryer, ran a vent brush through the in-wall duct all the way to the outside outlet, then took the dryer apart and cleaned the filter housing and internal airflow passages. The lint we pulled out is in the photos. Drying time went back to normal.

02Crushed and foil ducts

On a Samsung in Denver we replaced the user interface board and also fixed the vent duct, which was bent so sharply behind the dryer that it choked the airflow. Thin foil ducts like the one behind a Maytag in Denver crush easily when the dryer is pushed back. Semi-rigid metal duct with gentle bends works far better.

Heat pump dryers

Heat pump and ventless dryers

03Whirlpool heat pump dryer taking forever

A Whirlpool heat pump (ventless) dryer in Denver took far too long to dry. Heat pump dryers recirculate air through their own condenser and evaporator coils, and those coils had packed with lint. We partially disassembled the dryer, cleaned both coils and the entire airflow path and ducts, and replaced the moisture sensor.

Whirlpool heat pump dryer after the service
Whirlpool heat pump dryer after the service
No heat

Dryer running but not heating

04Samsung HE error

A Samsung dryer in Denver showed an HE (heating) error and ran cold. The heating element had failed, so we replaced it and tested the temperature through a full cycle. On another Denver dryer the element was fine but its electrical contacts had burned; we repaired the heater wiring instead of replacing parts that weren't broken.

05Thermal fuses and why they blow

A Maytag in Denver wasn't running at all. After resetting a tripped breaker we found a blown thermal fuse and a worn belt, replaced both and cleaned the airflow path. In Niwot an LG needed a thermal fuse, heater thermostat and belt, and in Erie an LG needed a safety thermostat and a cut-off fuse. A thermal fuse blows when the dryer overheats, almost always because of lint, so we clean the airflow every time we replace one.

06On video: new heating element

Samsung dryer in Northglenn with no heat: new element and rollers, and a vent check so the new element doesn't burn out too.

Samsung dryer in Northglenn: new heating element and drum rollers, plus a vent check, since a blocked vent burns out elements.
Noise

Squeaking, thumping and grinding

07Drum rollers and idler pulley

A Samsung dryer in Denver made a metal-on-metal grinding sound. We replaced all three drum rollers and the idler pulley and cleaned the dryer. A Whirlpool stacked dryer in Denver squeaked; we replaced the support wheels and pulley wheel and leveled it. On a Maytag in Denver the support wheel and the pulley bracket had worn out.

Maytag dryer after the support wheel repair
Maytag dryer after the support wheel repair

08Won't tumble

A dryer in Denver stopped tumbling because a rag had worked its way under the drum and jammed the belt. Another needed only a new belt. A Kenmore stacked on a washer was noisy and running hot; it needed a belt and a thorough cleaning.

09On video: a squeaky dryer fixed

Squeaks and thumps usually mean drum rollers or the rear bearing. Here's a GE dryer in Broomfield after both were replaced.

GE dryer in Broomfield that squeaked. New drum rollers and a rear drum bearing; the drum turns quietly again.
Gas dryers

Gas dryers

10Gas line and vent on an LG

An LG gas dryer in Denver needed its flexible gas supply line reconnected and its vent cleaned. Every gas connection gets a leak test before we leave. If you smell gas near a dryer, turn it off, leave the house and call Xcel Energy or 911 from outside.

From the parts list

What 230 dryer work orders say about Denver dryers

11No heat is the big one

In about 230 recent dryer work orders with a written repair, the heating element was the single most replaced part, in one job in four. The thermal fuse came up in about one job in eight, usually together with the element. Thermostats and thermistors appeared less often.

A blown thermal fuse is a symptom. Something made the dryer run hot, and in Denver-area homes that is almost always the vent. About one job in six included vent or duct cleaning or reattaching a duct that had come loose behind the dryer.

12Noise and a drum that will not turn

Belts came up in about one job in six, drum parts and rollers in about one in seven, and idler pulleys less often. A squeal or a rhythmic thump means rollers or the idler are wearing; a dryer that runs but does not tumble has a broken belt. Both are repairs we usually finish in one visit, because belts and rollers are on the truck.

Job records

Recent dryer repairs in and around Denver

WhereApplianceProblemWhat we did
DenverGE dryerNot dryingCleaned exhaust duct, in-wall vent to the outside and internal airflow
DenverWhirlpool heat pump dryerTakes too long to dryCleaned condenser and evaporator coils and airflow path, replaced moisture sensor
DenverSamsung dryerHE error, no heatReplaced heating element
DenverDryerNot heatingRepaired burnt heater wiring contacts
DenverSamsung dryerDisplay fault, poor dryingReplaced UI control board, fixed crushed vent duct
DenverMaytag dryerNot runningReplaced thermal fuse and belt, cleaned airflow
DenverSamsung dryerGrinding noiseReplaced three drum rollers and idler pulley
DenverWhirlpool stacked dryerSqueakingReplaced support wheels and pulley wheel, leveled
DenverMaytag dryerSqueakingReplaced support wheel and pulley bracket
DenverDryerWon't tumbleRemoved a rag jammed under the drum
DenverKenmore stacked dryerNoisy, running hotReplaced belt, internal cleaning
DenverLG gas dryerGas line and ventReconnected gas supply line, cleaned vent, leak test
NiwotLG dryerNot heatingReplaced thermal fuse, heater thermostat and belt
ErieLG dryerNot heatingReplaced safety thermostat and cut-off fuse

Problems are described as the customer reported them; repairs are taken from the technician's notes. No customer details are published.

Tips from our technicians

How to avoid the next dryer repair

Clean the lint screen after every load, and wash it with soapy water every few months if it holds water.

Have the vent cleaned once a year, to the outside outlet, not just the duct behind the dryer.

Use semi-rigid metal duct with as few bends as possible. Replace foil or plastic duct.

Leave a few inches behind the dryer so the duct isn't crushed.

On heat pump and condenser dryers, clean both filters and the condenser as the manual says. They clog faster than vented dryers.

Who we are

ABC Denver Appliance Repair is an independent, local repair company. Our technicians are EPA 608-certified, carry common parts on the truck and test every repair before they leave. Every repair comes with a 90-day parts and labor warranty.

Our record in Denver

183 dryers repaired in Denver

From our job records since 2024 (completed home jobs). No client details are published.

What Denver customers report

Not heating
 32
Not working
 26
Noisy
 24
Showing an error code
 8
Not drying
 7
Not starting
 5

Parts we replaced most

Heating element
 10
Drum rollers
 9
Drive belt
 8
Control board
 7
Thermal fuse
 2
Temperature sensor
 2

Brands we see most

LG
 19
Samsung
 19
Whirlpool
 17
Kenmore
 15
GE
 13
Maytag
 13

Recent dryer repairs in Denver

  • November 2026 · Whirlpool dryer — noisy
  • November 2026 · GE dryer — not drying
  • October 2026 · Kenmore dryer — noisy
  • October 2026 · Whirlpool dryer — not drying; replaced the drive belt
  • October 2026 · LG dryer — not working
  • October 2026 · Electrolux dryer — showing an error code
  • September 2026 · Dryer — noisy; replaced the drum rollers
  • September 2026 · Samsung dryer — noisy
Local conditions

Dryers in Denver: water and altitude

A dryer that takes two cycles in Denver usually has a vent problem, not a heater problem — clean the vent before replacing parts.

Denver's water is moderately hard (about 5.2 grains per gallon). Moderately hard water slowly builds scale in ice maker valves, dishwasher heaters and washer inlet screens. Rinse aid and regular filter changes go a long way.

At about 5,280 feet, water boils about ten degrees below 212°F and recipes behave differently than at sea level. That's normal. What isn't normal is a gas burner with a yellow or lifting flame — that's worth a service call.

Seasonality

When dryers break in Denver

In our records, the busiest months for dryers in Denver are October and November; the quietest is August. Booking early in a busy month gets you a faster appointment.

Completed jobs by month, 2024–2026.

JanFebMarAprMayJunJulAugSepOctNovDec
Brands

Dryer brands we repair in Denver

The brands below are the ones we see most in Denver, in order. We repair all major brands, standard and built-in.

Types

Types of dryers we service in Denver

Electric dryers

Electric dryers run on a 240-volt circuit and heat with a coil element. When they stop heating, the element, thermal fuse, thermostats or one leg of household power are the usual causes.

Gas dryers

Gas dryers use a burner with an igniter, flame sensor and gas valve. They heat faster and cost less to run but need careful service by a qualified technician.

Heat-pump and ventless dryers

Ventless dryers recycle air through a condenser or heat pump. They need clean filters and condensers and have pumps and sensors that standard dryers don't.

Stacked and laundry-center dryers

Upper dryers in stacked pairs or laundry centers require more effort to service; vent connections behind them are often crushed during installation.

Problems

Dryer problems we fix in Denver

Full dryer repair guide →

Dryer runs but doesn't heat

On electric dryers we test the heating element, thermal fuse, high-limit and cycling thermostats. On gas dryers, it's usually the igniter, flame sensor or gas valve coils.

Takes two or three cycles to dry

Nine times out of ten this is airflow: a lint-packed vent, a crushed transition duct behind the dryer, or a long vent run with too many elbows. We check the airflow before replacing heating parts.

Won't start or stops after a few minutes

We check the door switch, start switch, thermal fuse, belt switch and motor. A dryer that starts and shuts off after a few minutes often has an overheating motor or a failing thermal protector.

Thumping, squealing or scraping noise

Thumping usually means flat-spotted drum rollers; squealing comes from an idler pulley or worn drum glides; scraping is often a drum seal or a coin caught in the blower. All are routine repairs.

Burning smell

Turn the dryer off. Lint near the heater or burner, a failing motor or a belt rubbing are the usual causes.

Dryer leaves clothes damp at the end

A dirty moisture sensor, a restricted vent or an overloaded drum. Wiping the sensor bars with rubbing alcohol is a good first step.

Dryer heats but drum doesn't turn

A broken belt, a failed idler pulley or a motor problem. On many dryers a broken belt also stops the motor through a switch.

Dryer making squeaking noise at startup

Dry drum glides or a worn idler pulley are typical. These parts are inexpensive, and replacing them prevents belt damage.

Before you call

  1. Clean the lint screen and check the area below it for lint buildup.
  2. Pull the dryer out a little and check that the vent duct isn't crushed or disconnected.
  3. Go outside and check the vent hood while the dryer runs: you should feel strong airflow.
  4. For electric dryers, check both breakers or the double breaker; a single tripped side can let the drum turn without heat.
  5. For gas dryers, make sure the gas valve behind the dryer is open.

Repair or replace?

Most dryer repairs — heating parts, belts, rollers, switches — cost far less than a new dryer. A failed motor or control board on a very old machine is the main exception.

Try our repair-or-replace calculator →

Pricing

What affects the price of dryer repair in Denver

Service call from $59, credited toward the repair. Written price before any work.

  • Thermal fuses, thermostats, belts and rollers are moderate repairs; motors and control boards cost more.
  • Gas valve and igniter work takes longer than electric element replacement.
  • Stacked units and tight laundry closets take more time to access.

Keeping your dryer running in Denver

  • Clean the lint screen every load and wash it with soapy water every few months.
  • Have the full vent run cleaned at least once a year.
  • Replace foil or vinyl transition ducts with semi-rigid metal duct.
  • Don't overload — airflow through the clothes matters as much as heat.

How a home repair visit works

Step 1

Book

Call, text or send the form with the appliance, brand and model if you have it. We give you an arrival window.

Step 2

Diagnose & quote

The technician tests the appliance and gives you a written price before starting. The service call is credited if you go ahead.

Step 3

Repair & warranty

Most repairs are finished on the first visit with parts from the truck. Every repair carries our 90-day warranty.

Dryer repair in Denver: questions

My dryer runs but takes forever to dry. What is it?

Most often a restricted vent or lint inside the cabinet. We check airflow at the outlet first. If the vent is clear, we test the heating element, thermostats and moisture sensor.

My dryer has no heat. Is it the heating element?

Sometimes. On electric dryers it can be the element, a thermal fuse, a thermostat or the wiring. On gas dryers it's often the igniter or gas valve coils. A blown fuse usually means the vent is restricted, so we fix the cause too.

Why is my dryer squeaking or thumping?

Worn drum rollers, support wheels, the idler pulley or a belt. These are routine repairs, usually done the same visit.

Is a lint-clogged dryer dangerous?

Yes. Lint is flammable and a restricted vent makes the dryer run hot. If your dryer feels unusually hot or smells of burning, stop using it until it's checked.

Do you repair heat pump and ventless dryers?

Yes, including Whirlpool, LG, Samsung, Bosch and Miele heat pump and condenser dryers.

How soon can you come?

We offer same- or next-day appointments across Denver, subject to the schedule. Call early in the day for the best chance of a same-day visit.

Call (720) 534-0432