Home / Error codes / Heatcraft

Walk-in refrigeration · 27 codes

Heatcraft intelliGen Error & Alarm Codes

Walk-in cooler and freezer evaporators with the intelliGen Refrigeration Controller. Covers: intelliGen iRC (2023 manual)

Commercial service call$129
Waived when you approve the repairWritten quote before any work · same- or next-day appointments · 90-day warranty on parts and labor

How the codes appear

The OLED display shows the active ER (error), AL (alarm) or IN (information) code. The light bar turns yellow for an error and red for an alarm; the affected unit flashes.

Resetting

The manual does not describe an acknowledge or reset procedure; it mentions clearing alarm history in the alarm menu.

If the same code comes back after a reset, stop resetting it — repeated restarts can hide the real fault or damage components. Call a technician.

Heatcraft code list

ER01

Box Temp

Technician

Box temperature sensor fault.

Causes the manufacturer lists

  • Sensor or its connections
ER02

Coil Temp

Technician

Coil temperature sensor fault.

Causes the manufacturer lists

  • Sensor or its connections
ER03

EV Suc Temp

Technician

Evaporator suction temperature sensor fault.

Causes the manufacturer lists

  • Sensor or its connections
ER04

EV Suc Press

Technician

Suction pressure transducer fault.

Causes the manufacturer lists

  • Transducer or its connections
ER11

Control Circuit

Technician

Control circuit fault (only when a condensing unit is wired to the board); the troubleshooting guide relates it to safety trips.

Causes the manufacturer lists

  • Field wiring to the board
  • Low/high/oil pressure safety trip
  • Compressor module
  • Phase loss monitor
ER14

Power Supply Low

Technician

Board supply voltage fell below 18 VAC; the system may shut down and restart after power is restored.

Causes the manufacturer lists

  • Low supply voltage
ER15

Power Supply High

Technician

Board supply voltage is high.

ER16

Low Superheat

Technician

Unit ran 2 minutes below the low superheat setpoint; can occur during initial start-up.

ER19

Replace Battery / Set Time

Technician

Clock battery issue; time needs to be set.

Causes the manufacturer lists

  • Clock battery
ER22

UI Failure

Technician

User interface (display) failure.

Causes the manufacturer lists

  • Display harness
  • Display unit
ER27

High Humidity

Status / staff can check

Humidity sensor reading is high.

What staff can safely check

  • Keep the walk-in door closed
ER28

Low Humidity

Technician

Humidity sensor reading is low.

ER29

Humidity Sensor

Technician

Humidity sensor fault.

ER31

LL Conn Lost

Technician

Lead-lag connection to another system lost.

ER32

A2L Early Warning

Technician

Refrigerant leak detected below the mitigation level.

Causes the manufacturer lists

  • Refrigerant leak

What staff can safely check

  • Call for service promptly
ER33

A2L Sensor Fault

Technician

Refrigerant leak detection sensor fault.

ER34

A2L Service

Technician

Leak detection sensor needs service.

ER35

A2L Mitigation

Technician

Leak detection mitigation condition.

Causes the manufacturer lists

  • Refrigerant leak

What staff can safely check

  • Follow site safety procedures and call for service
ER37

A2L Mitigation Controller Comm Loss

Technician

Communication lost with the leak mitigation controller.

AL01

High Box Temp

Status / staff can check

Box temperature above the high alarm setpoint after the alarm delay (default 60 min); delayed further if the door was recently open a lot.

What staff can safely check

  • Make sure the walk-in door closes and seals
  • Limit door openings
AL02

Low Box Temp

Technician

Box temperature below the low alarm setpoint after the alarm delay.

AL03

System Startup

Technician

System start-up alarm (only when a condensing unit is wired).

AL04

Input Fault

Technician

Triggered by sensor errors ER01, ER03 or ER04.

AL06

Door Open

Status / staff can check

Door open longer than the door alarm time (default 60 min).

Causes the manufacturer lists

  • Door left open

What staff can safely check

  • Close the walk-in door fully
AL12

A2L Override

Technician

Leak mitigation mode is active: the shut-off valve closes and fans run.

Causes the manufacturer lists

  • Refrigerant leak detected

What staff can safely check

  • Follow site safety procedures and call for service
IN01

Too Many Defrosts

Technician

Defrost ended in under 5 minutes 8 times in a row.

IN05

Too Few Defrosts

Technician

Defrost ended on time (not temperature) 8 times in a row.

What staff can safely check

  • Report ice build-up on the evaporator coil

Seeing Heatcraft codes you can't clear?

Same- or next-day appointments across the Denver metro. Written quote before any work, EPA 608 certified technicians.

Request service

Model notes

Codes listed by name only in the manual without further detail were omitted (ER13, ER18, ER20, ER23-26, ER36, AL10, AL11). URL contains spaces; encode as %20 if linking.

Sources

Compiled and paraphrased from the manufacturer documents above. Codes differ between model years and control boards — confirm against the manual for your exact model. ABC Denver Appliance Repair is an independent service company, not affiliated with Heatcraft.

From our job records

Photos from our job records

Real photos our technicians took on calls around Denver and the Front Range. Each caption says what was done; no customer details are shown.

Freezer drawer temperature check after a control board replacement, Greenwood Village
Freezer drawer temperature check after a control board replacement, Greenwood Village
Maytag washer in Wheat Ridge after a water valve replacement
Maytag washer in Wheat Ridge after a water valve replacement
Freezer temperature check after a compressor replacement, Denver
Freezer temperature check after a compressor replacement, Denver
Gas range in Frederick, checked during a gas stove service call
Gas range in Frederick, checked during a gas stove service call

Call (720) 534-0432