E01
Long freeze cycle
Technician Freeze cycles are running too long. Repeated long freezes trip Safety Limit #1 (on firmware 5.010 and later: freeze longer than 35 minutes for 6 freeze cycles in a row).
Causes the manufacturer lists
- Improper installation
- Water pressure too low (under 20 psig) or too high (over 80 psig)
- Incoming water warmer than 90°F
- Dirty or defective water level probe, fill valve or dump valve
- Clogged water distribution tube
- Water pump defect or water loss from the sump
- Low incoming voltage
- Ice thickness probe out of adjustment
- Restricted airflow or dirty condenser fins, high inlet air temperature, or condenser discharge air recirculating
- Refrigeration faults (charge, head pressure control, harvest valve, TXV, compressor, non-condensables, restrictions)
What staff can safely check
- Make sure the water supply to the machine has not been shut off
- Keep the air path to the condenser clear and make sure hot discharge air is not blowing back into the machine
E02
Long harvest cycle
Technician Harvest cycles are running too long. Repeated long harvests trip Safety Limit #2 (on firmware 5.010 and later: harvest longer than 7 minutes for 3 harvest cycles in a row).
Causes the manufacturer lists
- Improper installation
- Dirty evaporator
- Dirty or defective water dump valve
- Missing vent tube on the water outlet drain
- Water freezing behind the evaporator
- Loose plastic extrusions or gaskets
- Clogged water distribution tube
- Ice thickness probe out of adjustment
- Bin switch closed or defective
- Premature harvest from water level probe circuit
- Refrigeration faults (charge, head pressure control valve, harvest valve, TXV flooding, fan cycling control, water regulating valve on water-cooled units)
E03
Input power loss
Status / staff can check The controller recorded a loss of incoming power.
E04
High condenser temperature
Technician The condenser temperature reading went too high.
E05
High pressure control opened
Technician The high-pressure safety switch opened.
E07
Starving TXV or low on charge
Technician The controller detected a refrigeration pattern consistent with a starving expansion valve or low refrigerant charge (single evaporator).
E08
TXV fault
Technician Expansion valve fault detected (single or dual circuit).
E09
#1 evaporator flooding
Technician Evaporator #1 is flooding with refrigerant.
E10
#2 evaporator flooding
Technician Evaporator #2 is flooding with refrigerant (dual-circuit machines).
E11
Refrigeration fault
Technician A general refrigeration system fault was detected.
E12
Curtain switch fault
Technician A water curtain switch stayed open too long (12 hours on E boards; 24 hours on G boards after firmware 4.017).
E15
Fan cycle control fault
Technician Fan cycling control fault, indicated by a low liquid line temperature.
E16
Remote condensing unit fault
Technician Fault with the remote condensing unit (ICVD / QuietQube models only).
E19
Ice thickness probe fault
Technician The ice thickness probe circuit is faulty.
E20
Water system fault
Technician A fault was detected in the water system.
E21
T1 temperature sensor issue
Technician Problem with temperature sensor T1.
E22
T2 temperature sensor issue
Technician Problem with temperature sensor T2.
E23
T3 temperature sensor issue
Technician Problem with temperature sensor T3.
E24
T4 temperature sensor issue
Technician Problem with temperature sensor T4.
E25
Bin level probe low sensor fault
Technician Fault in the low sensor of the bin level probe.
E26
Bin level probe medium sensor fault
Technician Fault in the medium sensor of the bin level probe.
E27
Bin level probe high sensor fault
Technician Fault in the high sensor of the bin level probe.
E28
AuCS
Technician Event related to the AuCS automatic cleaning system (the handbook gives no further description).
E29
USB communication fault
Technician Communication fault with the USB port.
E30
USB download fault
Technician A download through the USB port failed.
E31
Safe mode
Technician The controller entered its safe operation mode.
E32
RS485 communication fault
Technician Internal RS485 communication fault between controller components.
E33
Keyboard fault
Technician Fault with the front keypad.
E34
Display fault
Technician Fault with the display.