Home / Error codes / Ice-O-Matic

Ice machines · 7 codes

Ice-O-Matic CIM Error Codes (Elevation)

Elevation Series CIM modular and self-contained cubers (CIM0320-CIM2046). Covers: CIM control board (incl. board 9101414-01 Rev B and later; some codes differ on pre-2106 boards)

Commercial service call$129
Waived when you approve the repairWritten quote before any work · same- or next-day appointments · 90-day warranty on parts and labor

How the codes appear

Errors are shown by flash patterns of the red POWER LED, and for some codes the yellow CLEAN LED as well (quick flashing, double flashes, or triple flashes followed by a pause).

Resetting

Press and hold the POWER and CLEAN buttons together for 3 seconds; a single blue/yellow flash confirms that error codes and counters are cleared.

If the same code comes back after a reset, stop resetting it — repeated restarts can hide the real fault or damage components. Call a technician.

Ice-O-Matic code list

Error 1 (POWER red, quick flash)

Max freeze / max harvest

Technician

The freeze cycle exceeded 1 hour and/or harvest exceeded its maximum time. Max freeze under this code applies to pre-2106 boards only.

Error 2 (POWER red, slow flash, in OFF state)

Thermistor failure

Technician

The board detected a failed temperature thermistor.

Error 3 (POWER red + CLEAN yellow, quick flash)

Max fill

Technician

The water fill took longer than 5 minutes during production (on pre-2106 boards this code also covers max purge).

What staff can safely check

  • Confirm the water supply is turned on and the water filter is not clogged (manual calls for 20-80 psi supply and a filter)
Error 4 (POWER double red + CLEAN double yellow, quick)

Max purge

Technician

The water purge (drain) took longer than 2 minutes.

Error 5 (POWER double red, quick)

Max harvest

Technician

Harvest ran longer than the 7.5 minute maximum.

Error 6 (POWER triple red, quick)

Max freeze and max harvest

Technician

Both the 1 hour freeze limit and the 7.5 minute harvest limit were exceeded.

Error 7 (POWER triple red + CLEAN triple yellow, quick)

Water level error

Technician

After the water pump started, the high float switch did not close (water level did not drop as expected). The board cycles the pump, and if the float still does not close it shuts the machine off to avoid running the evaporator without water.

Causes the manufacturer lists

  • Faulty or stuck water pump
  • Faulty pump relay on the control board
  • Broken wiring between pump and board
  • High float switch stuck up or its wiring broken
  • Water inlet valve leaking through (high water pressure, defective valve, debris or trapped air)
  • Little or no purge during harvest (bad purge valve, wiring or relay, or back pressure from poorly run or unvented drains)

Seeing Ice-O-Matic codes you can't clear?

Same- or next-day appointments across the Denver metro. Written quote before any work, EPA 608 certified technicians.

Request service

Model notes

The 2025 manual's table lists max harvest as 5.5 min under Error 1 but 7.5 min under Error 5 and the timing table (pre-2106 boards used a 5 min max harvest); avoid quoting an exact harvest time for Error 1. Diagnostic mode is entered by holding POWER and CLEAN for 6 seconds. Per-code causes are only published for Error 7. Manual's general owner items: dedicated circuit (no GFI), 20-80 psi water at 40-100°F, water filter installed, 6 in. clearance at rear/top/sides for air-cooled units, ambient 50-100°F.

Sources

Compiled and paraphrased from the manufacturer documents above. Codes differ between model years and control boards — confirm against the manual for your exact model. ABC Denver Appliance Repair is an independent service company, not affiliated with Ice-O-Matic.

From our job records

Photos from our job records

Real photos our technicians took on calls around Denver and the Front Range. Each caption says what was done; no customer details are shown.

Bosch microwave heating again after magnetron and thermal fuse replacement
Bosch microwave heating again after magnetron and thermal fuse replacement
Temperature check after a GE inverter board replacement, Denver
Temperature check after a GE inverter board replacement, Denver
Bosch gas cooktop and wall oven in Denver after a gas valve replacement
Bosch gas cooktop and wall oven in Denver after a gas valve replacement
Viking range back in service
Viking range back in service

Call (720) 534-0432